![]() ![]() Once you have 3 sheets of veneer hung, take a step back and inspect your work. Now your woodgrain should align perfectly. Double cut through both pieces of veneer and remove the access material. Next, make an incision on the double seam at the top and bottom. Repeat the same process for the third piece of veneer in your sequence. Then remove the excess veneer at the top and bottom. Once aligned, press the veneer down to remove any air bubbles. Slightly raise the second piece of veneer and align the woodgrain to match. It will overlap with the first piece of veneer. ![]() Starting from the top, hang your next piece of veneer along your second vertical line, but don’t press it down yet. Trim off the excess veneer using a straight edge and new razor blade. Beginning from left to right, hang your first piece of veneer making sure the right edge is following your straight, vertical line. Cover the area needed for three sheets of wood veneer. Add at least two inches to that measurement and cut your veneer to length.Īpply an even coat of PRO-732 Extra-Strength Clay on the wall. Mark your lines at the net width to account for overlap. Draw all your vertical lines along the desired length to be covered. Once it’s time to start hanging your wallcovering, draw a vertical line using a level or plumb line at your desired starting point. It’s important to allow the proper time for the adhesive to tack after it’s been applied to prevent bubbling after installation. Book the sheets and let sit for 20 minutes. Make sure that the entire backside of the sheet is coated. Next you’ll want to apply a uniform layer of the Roman PRO-732 extra strength clay adhesive using a standard ⅜ to ¾ inch nap paint roller. Once all of the sheets have been lightly dampened, roll the sheets and let sit for 20 minutes while the wall is prepared for application. Lightly dampen the back of three sheets of wallcovering with a cellulose sponge. You’ll want to overlap and double cut all your seams with a razor blade. Factory trimmed edges must not be butt jointed during installation. You’ll want to make sure that the pieces always match up bottom to bottom or top to top depending on the preferred orientation of your woodgrain.Īt this point you’ll want to take the measurement of the gross width of your roll of veneer and calculate your nominal width, or net width. End matching is crucial in order to have the woodgrain of your veneer align properly. We recommend that you lay your sheets end-to-end on the floor. It is important that the wallcovering is installed from left to right in numerical order. On the bottom backside of each sheet of veneer is a flitch number and a sequence number. When priming your wall, make sure that you follow the recommended spread rate and dry time. If your wall has been previously covered or painted, lightly sand the surface in order to break the seal prior to applying the primer. This can be checked with a moisture meter if necessary.īefore applying your wallcovering, prepare the drywall by priming it with PRO-977 Ultra Prime. Moisture content in the wall substrate should be in around 9% or less. When preparing the surface for your wallcovering, it is important to make sure that the surface is smooth and clean. This will help the sheets rest and acclimate to the environment. Let the sheets of wallcovering rest for 48 hours. Cover them with a sheet of vinyl and then place a sheet of plywood on top of the vinyl. When preparing your wallcovering, carefully remove them from the box and lay them face down flat on a table. We recommend that you store your wall covering in a low humidity environment that holds a stable temperature range between 45 to 85 degrees Fahrenheit. When storing your wall covering make sure that it is kept in a clean, dry, and secure area. If damage has occurred to the product, let the carrier know immediately and do not continue with the installation. Adhesive – PRO-732 Extra-Strength Clay Wallcovering Adhesiveįirst, make sure that your wallcovering was delivered undamaged.Primer – PRO-977 Ultra Prime Wallpaper Primer.How to Install Real Wood Veneer Wallcovering Recommended Primer and Adhesive: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |